To Cut
1. Make cutting sandwich (stack from bottom up):

Plate A
Plate C
Spellbinders Die (ridged side up)
Paper or cardstock
Plate B

2. Run through Cuttlebug™ machine

To Emboss
1. Make embossing sandwich (stack from bottom up):

Plate A
Spellbinders Die face up on A plate with die cut still in the die
Spellbinders Tan Embossing Mat
Two to three pieces cardstock as a shim
Two acrylic B plates

2. Run through Cuttlebug™ machine

To Cut
1. Make cutting sandwich (stack from bottom up):

Big Shots™ thick white mat 
Spellbinders White Spacer Plate 
Spellbinders Die (ridged side up)
Paper or cardstock
Two Big Shot acrylic mats

2. Roll through the BigShot™ machine.

To Emboss
1. Make embossing sandwich (stack from bottom up):

Remove Spellbinders Spacer Plate while leaving die cut still in die
Place Spellbinders Tan Embossing Mat over the paper and die
Three pieces cardstock as a shim
Put two Big Shot acrylic mats on top

2. Roll Through Big Shot machine

To Cut
1. Make cutting sandwich (stack from bottom up):

Large platform with all tabs closed
Spellbinders Die (ridged side up)
Cardstock or paper
Two Big Shot™ acrylic mats

2. Roll through Big Shot™ machine

To Emboss
1. Make embossing sandwich (stack from bottom up):

Remove acrylic mats while leaving die cut still in die on the multi-purpose platform
Place two Spellbinders Tan Embossing Mats on top of die
Tri-fold one piece of 12" x 6" cardstock for a shim and place on top of the Tan Embossing Mats
Place one Big Shot acrylic plate on top

2. Run through the Big Shot machine

To Cut
1. Make cutting sandwich (stack from bottom up):
2. Roll through Big Kick™ machine

To Emboss
1. Make embossing sandwich (stack from bottom up):
2. Run thru the Big Kick machine

To Cut & Emboss
1. Place a Spellbinders Die on ZEM’s platform, blade side up
2. Place paper over die and cut in the same manner as with Zip’e Cuts
3. After cutting, leave the die and paper on the platform to emboss.
4. Place ZEM’s Embossing Foam over paper and with the ZEM’s Embossing Mat, roll thru again to emboss the die-cut.

To Cut
1. Place the Sizzix® System Converter into the Sizzix® Machine
2. On the Cutting Pad, place paper to be cut, then Spellbinders Die, ridged side down
3. Place the Spellbinders Spacer Plate over the Spellbinders Die
4. Tri-fold one piece of 12" x 6" cardstock for a shim and place on top of the Spellbinders Spacer Plate
5. Push through Sizzix® Machine

To Emboss
1. After Cutting Die in Sizzix® Machine, remove paper shim and spacer plate
2. Leave paper die cut in the die
3. Turn over Spellbinders Die, placing it on Sizzix® cut pad
4. Place Spellbinders Tan Embossing Mat on top of Spellbinders Die
5. Place paper shim on top of Tan Embossing Mat
6. Push through Sizzix® Machine to emboss the Spellbinders Die
(Note: It may take several presses to cut larger Spellbinders Dies)

To Cut
1. Place die (ridged side up) onto Revolution platform
2. Place paper or cardstock on top of die
3. Place acrylic cutting mat on top of die
4. Roll through Revolution machine.

To Emboss
1. Remove acrylic cutting mat
2. Leave die in place with die cut still inside die
3. Place Spellbinders Tan Embossing Pad on top of die
4. Place acrylic embossing mat on top of Spellbinders Tan Embossing Pad
5. Roll through Revolution machine